[ { "product_id": "117", "product_title": "CU Later Copper Stain Remover", "product_content": "Extra strength 2 PART stain remover specially designed for COPPER STAINING on swimming pool surfaces.Lo-Chlor CU LATER PART I and PART II have been specially formulated TO WORK IN UNISON to remove COPPER STAINING from swimming pools. Lo-Chlor CU LATER PART I is a strong oxidiser and is specifically designed to enhance the performance of Lo-Chlor  CU LATER PART II. Lo-Chlor CU LATER PART II contains a special blend of organic & inorganic acids and has been expressly developed to remove COPPER STAINING from swimming pool surfaces.  DIRECTIONS FOR USE:Adjust pH to 7.0 and make sure that the chlorine level is below 1ppm before applying products. Over the discoloured area where copper stain has occurred, add 1kg of LO-CHLOR CU LATER PART I per 50,000 litres pool water with pump and filter running. After a colour change occurs wait 5 minutes then add LO-CHLOR CU LATER PART II Add 1 Kg of LO-CHLOR CU LATER PART II per 50,000 litres pool water. Product may be sprinkled directly over stained area or evenly distributed around the pool. CAUTION: When using in QUARTZON, COLOURED PEBBLE, COLOURED MARBLE, EXPOSED AGGREGATE finishes or PRINTED VINYL LINERS do not allow direct contact with the pool surface. In these cases it is recommended that you MIX IT IN A BUCKET OF WATER and DISPERSE AROUND THE POOL EVENLY. Run pump and filter for a minimum of 24 hours then resume normal filtration. LO-CHLOR CU LATER PART II is a strong acid mixture and when added to the pool water it will reduce pool water pH and Total Alkalinity. Pool water must be re-balanced following use of LO-CHLOR CU LATER PARTS I and II. Consult your pool professional for advice on re-balancing pool water. SPOT STAININGFor less severe SPOT STAINING we recommend that you proceed with STEPS 1 to 3 then prior to STEP 4, you add a small amount of LO-CHLOR CU LATER PART II to a sock or stocking then attach to the end of a telepole and dangle close to but not directly touching the stain and see if this removes the stain. If no sign of improvement is shown after a few minutes, revert to procedure in STEP 4. IMPORTANTAfter staining has been removed, LO-CHLOR METAL SOLUTION and FILTER AID AND METAL REMOVER should be used to remove dissolved metals from the water and prevent re-staining. Most COPPER STAINING forms due to INCORRECTLY BALANCED WATER or INFERIOR COPPER BASED ALGAECIDES. ", "product_order": "6", "product_icon": "\/media\/commerce_products\/117\/copper-stain-remover.jpg", "product_brand_id": "9", "product_price": "0.0000", "product_price_ex_tax": 0, "product_price_local_tax": "0.0000", "product_created_datetime": "2020-06-25 00:00:00", "product_code": "", "product_barcode": "", "product_is_unorderable": "0", "product_is_shipping_required": "0", "product_inventory_level": null, "product_uri": "\/products\/copper-stain-remover\/" }, { "product_id": "113", "product_title": "Iron Stain Remover", "product_content": "High strength formulation specially designed to remove BROWN IRON STAINS from swimming pool surfaces. Lo-Chlor IRON STAIN REMOVER contains a special acid blend and has been specifically developed to remove BROWN IRON STAINS from swimming pool surfaces. DIRECTIONS FOR USE:Allow Free Chlorine level to fall below 0.5 PPM by switching off the Salt Chlorinator or using Lo-Chlor CHLORINE REMOVER. Adjust pH to 7.2 to 7.6. Add 1 Kg of Lo-Chlor IRON STAIN REMOVER per 50,000 litres pool water with pump and filter running.  Product may be sprinkled directly over stained area or evenly distributed around the pool. CAUTION: When using in QUARTZON, COLOURED PEBBLE, COLOURED MARBLE, EXPOSED AGGREGATE finishes or PRINTED VINYL LINERS do not allow direct contact with the pool surface. In these cases it is recommended that you MIX IT IN A BUCKET OF WATER and DISPERSE AROUND THE POOL EVENLY. Run pump and filter for a minimum of 24 hours then resume normal filtration. Pool water must be re-balanced following use of  Lo-Chlor IRON STAIN REMOVER Consult your pool professional for advice on re-balancing pool water SPOT STAININGFor less severe SPOT STAINING we recommend that you add a small amount of Lo-Chlor IRON STAIN REMOVER to a sock or stocking then attach to the end of a telepole and dangle close to but not directly touching the stain and see if this removes the stain. If no sign of improvement is shown after a few minutes, revert to procedure as above. Most IRON STAINING forms due to INCORRECTLY BALANCED WATER", "product_order": "2", "product_icon": "\/media\/commerce_products\/113\/iron-stain-remover.jpg", "product_brand_id": "9", "product_price": "0.0000", "product_price_ex_tax": 0, "product_price_local_tax": "0.0000", "product_created_datetime": "2020-06-24 00:00:00", "product_code": "", "product_barcode": "", "product_is_unorderable": "0", "product_is_shipping_required": "0", "product_inventory_level": null, "product_uri": "\/products\/lo-chlor-iron-stain-remover\/" }, { "product_id": "112", "product_title": "Lo-Chlor Multi Stain Remover", "product_content": "TRIPLE ACTION ALL PURPOSE Stain Remover Will Remove All types of METALLIC & ORGANIC STAINS From Swimming Pool And Spa Surfaces Benefits Removes iron, copper, manganese and rust stains Also removes organic stains such as algae stains, leaf stains and mould in vinyl liners Use as an all over treatment for stain removal or as a spot treatment Dosage1KG treats up to 50,000 Litres pool water Important NotesAvoid applying Multi-Stain Remover directly to a vinyl liner or painted surface as damage may result to the pool surface For vinyl liner spot treatment, place Multi-Stain Remover in sock or panty hose, attach to telescopic pole and suspend over stained area For stains throughout a vinyl liner pool, dissolve Multi-Stain Remover in a bucket of water and pour around the perimeter of the pool After treatment a reduction in pH and\/or total alkalinity may occur. If adding a pH adjuster (sodium bicarbonate) then do so very, very slowly. Raising the pH and\/or total alkalinity too quickly can cause a cloudy pool as well as re-depositing the stain back on the pool surface Be aware that high levels of chlorine will reduce the effectiveness of Multi-Stain Remover. Ideally, reduce the chlorine level to zero before using this product What happens when a pool interior stains?All swimming pools interiors are made from chemical compounds of one type or another. Staining problems can start even before we commence filling the pool with water. Water is corrosive so it must be balanced by careful addition of certain chemicals. Added to this we must sanitize the water continually and re­check the balance to ensure the pool interior is not being attacked by the water itself and also to ensure that bathers are swimming in correctly treated water.Staining occurs when insoluble chemical precipitates form in the pool.These may deposit on the pool interior and often they are hard to remove.For our purposes stains fall into two categories: Vegetable stains caused by falling leaves and other plant matter and metal stains caused by dissolved metals in the pool water.", "product_order": "1", "product_icon": "\/media\/commerce_products\/112\/lochlor-multi-stain-remover.jpg", "product_brand_id": "9", "product_price": "0.0000", "product_price_ex_tax": 0, "product_price_local_tax": "0.0000", "product_created_datetime": "2020-06-24 00:00:00", "product_code": "", "product_barcode": "", "product_is_unorderable": "0", "product_is_shipping_required": "0", "product_inventory_level": null, "product_uri": "\/products\/lo-chlor-multi-stain-remover\/" }, { "product_id": "116", "product_title": "Lo-Chlor Stain and Scale Defense", "product_content": "## Lo-Chlor Stain & Scale Defense. A dispersant and scale inhibitor that is used to reduce and prevent scale formation, staining and corrosion in swimming pools. Using Lo-Chlor Stain and Scale Defence as part of a swimming pool maintenance program will reduce and inhibit scale formation as well as remove existing scale. Helps prevent rust discolouration and staining, scum formation and plugging of filters.### Features Reduces and prevents scale formationHelps prevent rust stainingReduces scum formationPrevents corrosion of metal partsRegular use will keep pool water sparkling and extend life of pool surface and equipment", "product_order": "5", "product_icon": "\/media\/commerce_products\/116\/stain-scale-defense.jpg", "product_brand_id": "9", "product_price": "0.0000", "product_price_ex_tax": 0, "product_price_local_tax": "0.0000", "product_created_datetime": "2020-06-24 00:00:00", "product_code": "", "product_barcode": "", "product_is_unorderable": "0", "product_is_shipping_required": "0", "product_inventory_level": null, "product_uri": "\/products\/stain-and-scale-defense\/" }, { "product_id": "114", "product_title": "Salt Stain Remover", "product_content": "For The Removal Of BROWN IRON STAINSAnhydrous blend of Citric acid and other inert ingredientsFeatures & BenefitsRemoves stains caused by iron in swimming pools Can be used on all surfaces Ideal for pools where salt stains are common Dosage and application1Kg treats 50,000 Litres pool water Tips from the stain experts...Iron and Manganese stain removalRemove Chlorine and ensure pH is 7.2 to 7.6. Add 1 Kg of Lo-Chlor Salt Stain Remover, by sprinkling around the outside of the pool. Filter as normal. The stain should be gone within twelve hours. If in the unlikely event this does not remove all the stain, repeat with another 1 Kg. When the stain is gone, add 1 Litre of Lo-Chlor Metal Solution. Do not Superchlorinate for 10 days after adding Metal solution, or the stain will return immediately. It takes about 10 days to 2 weeks for Metal Solution to get rid of a stain. If the stain was severe it may be necessary, after stain removal, to adjust pH to 7.8 to 8.0 and add 1 Litre Lo-Chlor Maxi Floc Plus. Making the pool alkaline and then floccing will remove about 70% of the dissolved metals. Leave overnight and then vacuum to waste. Balance the water and then add 1 Litre of Lo-Chlor Metal Solution. For a salt water pool this treatment may need to be repeated every six months!", "product_order": "3", "product_icon": "\/media\/commerce_products\/114\/salt-stain-remover.jpg", "product_brand_id": "9", "product_price": "0.0000", "product_price_ex_tax": 0, "product_price_local_tax": "0.0000", "product_created_datetime": "2020-06-24 00:00:00", "product_code": "", "product_barcode": "", "product_is_unorderable": "0", "product_is_shipping_required": "0", "product_inventory_level": null, "product_uri": "\/products\/lo-chlor-salt-stain-remover\/" }, { "product_id": "115", "product_title": "Stain and Scale Attack", "product_content": "A two part pack which attacks calcium scale in swimming poolsTwo highly concentrated formulations from Lo-Chlor Chemicals which combine to form a concentrated compound of organic acids and chelating agents in the fight against Calcium Scale in swimming pools.Features & BenefitsConcentrated calcium scale remover Can also be used as an effective copper stain remover Lo-Chlor Scale Attack works best at pH 7.0. Make sure the Chlorine level is below 1.0 p.p.m. High chlorine levels will neutralise Scale Attack Lo-Chlor Scale Attack works very slowly. Advise the pool owner it will take up to 6 weeks before results are sometimes seenRun pump, filter and Chlorinator, as normal Do not sprinkle onto pool surface. Must ALWAYS be mixed in a bucket of water first Sizes2 x 1Kg Pack Treats up to 50,000L water DosageAdd 1Kg Scale Attack Part I to bucket of water and mix until dissolved Then add 1Kg Scale Attack Part II to the same solution Once mixed thoroughly pour around perimeter of pool A few facts from the professionals...After the solution is mixed thoroughly try to pour over as great an area as possible. Immediately after the addition of Scale Attack the pool will go cloudy. This cloudiness should disappear within 5-10 minutes Allow to filter for at least 24 hours after application. Re balance pool after 5-7 days. Allow at least 4-6 weeks before you can expect to see any results. To prevent the build up of new calcium scale in swimming pools add Lo-Chlor Scale Defence at a rate of 5L per 50,000L", "product_order": "4", "product_icon": "\/media\/commerce_products\/115\/stain-and-scale-attack.jpg", "product_brand_id": "9", "product_price": "0.0000", "product_price_ex_tax": 0, "product_price_local_tax": "0.0000", "product_created_datetime": "2020-06-24 00:00:00", "product_code": "", "product_barcode": "", "product_is_unorderable": "0", "product_is_shipping_required": "0", "product_inventory_level": null, "product_uri": "\/products\/lo-chlor-stain-and-scale-attack\/" } ]